Departamento
Ciencia de los Materiales e Ingeniería Metalúrgica
Artículos (24) Publicaciones en las que ha participado algún/a investigador/a
2009
-
Above burden temperature data probes interpretation to prevent malfunction of blast furnaces - Part 1: Intelligent information preprocessing
Steel Research International, Vol. 80, Núm. 3, pp. 185-193
-
Aplicación del permanganato potásico para la eliminación de cianuros de cobre en aguas residuales de la planta de lixiviación en una mina de oro (I)
Revista de metalurgia, Vol. 45, Núm. 6, pp. 415-423
-
Aspectos Microestructurales de la corrosión química en un convertidor (PSC)
Boletín de la Sociedad Española de Cerámica y Vidrio, Vol. 48, Núm. 5, pp. 231-236
-
Bottom design optimisation of electric arc furnace for ferromanganese production using nodal wear model
Ironmaking and Steelmaking, Vol. 36, Núm. 7, pp. 529-536
-
Características sólido-fluido en el crisol del horno alto según el modelo de desgaste nodal (MDN)
Revista de metalurgia, Vol. 45, Núm. 4, pp. 295-304
-
Contact fatigue damage analysis of shot peened gears by means of X-ray measurements
Engineering Failure Analysis, Vol. 16, Núm. 3, pp. 964-971
-
Determinación de los coeficientes de capa límite mediante el Modelo de Desgaste Nodal (MDN) para el estudio de la corrosión del crisol de alto horno
Boletín de la Sociedad Española de Cerámica y Vidrio, Vol. 48, Núm. 3, pp. 153-156
-
Effect of mechanical mismatching on the ductile-to-brittle transition curve of welded joints
Engineering Failure Analysis, Vol. 16, Núm. 8, pp. 2576-2585
-
Energy consumption as a predictor test of the durability of a biological tissue employed in cardiac bioprosthesis
Journal of Biomedical Materials Research - Part A, Vol. 89, Núm. 2, pp. 336-344
-
Fatigue behaviour of duplex stainless steel reinforcing bars subjected to shot peening
Fatigue and Fracture of Engineering Materials and Structures, Vol. 32, Núm. 7, pp. 567-572
-
Fractography and failure mechanisms in static mode I and mode II delamination testing of unidirectional carbon reinforced composites
Polymer Testing, Vol. 28, Núm. 6, pp. 612-617
-
Fracture characterization of ductile polymers through methods based on load separation
Polymer Testing, Vol. 28, Núm. 2, pp. 204-208
-
High temperature oxidation of plasma and hvof thermal sprayed CoNiCrAlY coatings in simulated gas turbine and furnace environments
Surface Engineering, Vol. 25, Núm. 4, pp. 319-325
-
Influence of shot peening process on contact fatigue behavior of gears
Materials and Manufacturing Processes, Vol. 24, Núm. 12, pp. 1436-1441
-
Inverse determination of the elastoplastic and damage parameters on small punch tests
Fatigue and Fracture of Engineering Materials and Structures, Vol. 32, Núm. 11, pp. 872-885
-
Leaching behaviour of a Bayer electrofilter fines in sulphuric acid
Hydrometallurgy, Vol. 96, Núm. 1-2, pp. 35-41
-
Machinability improvement through heat treatment in 8620 low-carbon alloyed steel
Machining Science and Technology, Vol. 13, Núm. 4, pp. 529-542
-
Mechanical properties characterization of heat-affected zone using the small punch test
Welding Journal (Miami, Fla), Vol. 88, Núm. 9
-
Numerical and experimental validation of computational models for mode I composite fracture failure
Computational Materials Science, Vol. 45, Núm. 4, pp. 993-998
-
Synthesis and characterization of microporous titanosilicate ETS-10 obtained with different Ti sources
Materials Research Bulletin, Vol. 44, Núm. 6, pp. 1225-1231