Publicaciones en las que colabora con Jaime Viña (44)

2023

  1. Estudio del comportamiento a fatiga de la delaminación bajo la influencia de un ambiente salino en uniones adhesivas en composites epoxi reforzados con fibra de carbono

    Revista española de mecánica de la fractura, Núm. 6, pp. 191-196

2022

  1. Study of the fatigue delamination behaviour of adhesive joints in carbon fibre reinforced epoxy composites, influence of the period of exposure to saline environment

    Scientific reports, Vol. 12, Núm. 1, pp. 19789

2020

  1. Mechanical properties of fibreglass and carbon-fibre reinforced polyetherimide after twenty years of outdoor environmental aging in the city of Gijón (Spain)

    Composites Communications, Vol. 22

  2. Study of the influence of the type of matrix used in carbon-epoxy composites on fatigue delamination under mode III fracture

    Materials and Design, Vol. 186

  3. Symmetric and asymmetric dynamic characterization of mode-III fracture in epoxy/unidirectional carbon-fibre composites

    Fatigue and Fracture of Engineering Materials and Structures, Vol. 43, Núm. 3, pp. 457-465

2019

  1. Influence of the test method on the characterization of the fatigue delamination behavior of a composite material under mixed mode I/II fracture

    Polymers, Vol. 11, Núm. 11

  2. Use of a LHFB device for testing mode III in a composite laminate

    Polymers, Vol. 11, Núm. 8

2017

  1. A study of the effects of the matrix epoxy resin and graphene oxide (GO) manufacturing process on the tensile behaviour of GO-epoxy nanocomposites

    Plastics, Rubber and Composites, Vol. 46, Núm. 9, pp. 405-412

  2. Analysis of mode III interlaminar fracture toughness of laminated composites using a novel testing device

    Engineering Fracture Mechanics, Vol. 173, pp. 55-63

2014

  1. Influence of low temperatures on the phenomenon of delamination of mode I fracture in carbon-fibre/epoxy composites under fatigue loading

    Composite Structures, Vol. 112, Núm. 1, pp. 188-193

2013

  1. Influence of the matrix toughness in carbon-epoxy composites subjected to delamination under modes i, ii, and mixed I/II

    Mechanics of Advanced Materials and Structures, Vol. 20, Núm. 8, pp. 679-686

2012

  1. Analysis of the influence of the temperature in the process of delamination under static and dynamic solicitation of an unidireccional carbon-epoxy composite

    ICEM15: 15th International Conference on Experimental Mechanics

  2. Influence of temperature on a carbon-fibre epoxy composite subjected to static and fatigue loading under mode-I delamination

    International Journal of Solids and Structures, Vol. 49, Núm. 21, pp. 2934-2940

2011

  1. Influence of the matrix constituent on mode i and mode II delamination toughness in fiber-reinforced polymer composites under cyclic fatigue

    Mechanics of Materials, Vol. 43, Núm. 1, pp. 62-67

  2. Influence of the mode mixity ratio and test procedures on the total energy release rate in carbon-epoxy laminates

    Procedia Engineering

  3. Influencia de la relación de mixticidad y de los procedimientos de ensayo sobre la tasa de relajación de energía en laminados carbono epoxi

    Actas del IX Congreso Nacional de Materiales Compuestos: Girona, 5, 6, 7 y 8 de julio de 2011

2010

  1. Compliance correction for numerical and experimental determination of mode i and mode II composite fracture failure

    Mechanics of Advanced Materials and Structures, Vol. 17, Núm. 5, pp. 377-381

2009

  1. Fractography and failure mechanisms in static mode I and mode II delamination testing of unidirectional carbon reinforced composites

    Polymer Testing, Vol. 28, Núm. 6, pp. 612-617

  2. Numerical and experimental validation of computational models for mode I composite fracture failure

    Computational Materials Science, Vol. 45, Núm. 4, pp. 993-998

2008

  1. A comparison between the behavior of glass and carbon fiber fabric reinforced PEI subjected to hygrothermal loads

    Journal of Advanced Materials, Vol. 40, Núm. 3, pp. 17-25